Class 9 Physical Science · chapter 1: Matter in Our Surroundings · lesson 3 of 12

Change of state, latent heat and evaporation

About 45 minutes

Why this matters

Change of state and evaporation give the most marks in this chapter. Expect a two-mark question on latent heat or sublimation, a three-mark question on the factors affecting evaporation, and a question on why evaporation causes cooling. The kelvin conversion from the last lesson is used again here.

The idea

Water is ice in a freezer, liquid in a glass and steam in a kettle. Matter changes its state when we change its temperature or its pressure.

Effect of change of temperature

Heat ice in a beaker with a thermometer. The temperature rises until the ice starts melting, then stays constant until all the ice has become water, and then rises again. The melting point is the temperature at which a solid melts to become a liquid at atmospheric pressure. The textbook gives the melting point of ice as 273.16 K, which is 0 °C. The change of a solid to a liquid by heating is fusion. During melting the heat supplied does not raise the temperature; it is used to overcome the forces of attraction between particles. This hidden heat is called latent heat. The latent heat of fusion is the amount of heat energy required to change 1 kg of a solid into liquid at its melting point at atmospheric pressure. For ice it is 3.34 × 10⁵ J/kg. So water at 273 K has more energy than ice at 273 K.

Keep heating and the water boils. The boiling point is the temperature at which a liquid starts boiling at atmospheric pressure; for water it is 373 K (100 °C). Boiling is a bulk phenomenon, meaning particles from the whole of the liquid gain enough energy to change into vapour. The latent heat of vaporisation is the heat energy required to change 1 kg of a liquid into gas at its boiling point at atmospheric pressure. For water it is 22.5 × 10⁵ J/kg. Steam at 373 K therefore carries far more energy than water at 373 K, which is why a steam burn is worse than a hot-water burn.

Some solids skip the liquid state. Sublimation is the change of state directly from solid to gas, or from gas to solid, without passing through the liquid state. Camphor, ammonium chloride, naphthalene balls and iodine sublime.

Effect of change of pressure

Push the particles of a gas closer by applying pressure and cool it, and it becomes a liquid. This is how LPG is made. Solid carbon dioxide (dry ice) is stored under high pressure; when the pressure is reduced to 1 atmosphere it turns directly into gas without becoming liquid, so it is called dry ice. Pressure and temperature together decide the state of a substance.

ChangeName
Solid → liquidMelting (fusion)
Liquid → gasVaporisation (boiling)
Gas → liquidCondensation
Liquid → solidFreezing (solidification)
Solid → gas directlySublimation
Gas → solid directlyDeposition

Evaporation

Wet clothes dry even in the shade, well below 100 °C. Evaporation is the change of a liquid into vapour at any temperature below its boiling point, from the surface of the liquid. A few particles at the surface have higher kinetic energy than the rest and escape into the air. Because only surface particles leave, evaporation is a surface phenomenon. Four factors increase the rate of evaporation.

  • Surface area: a larger surface exposes more particles, so clothes are spread out to dry.
  • Temperature: a higher temperature gives more particles enough energy to escape.
  • Humidity: humidity is the amount of water vapour already present in the air; high humidity slows evaporation, which is why clothes dry slowly on a rainy day.
  • Wind speed: moving air carries vapour away, so clothes dry faster on a windy day.

Evaporation causes cooling. The escaping particles take the energy they need from the liquid and its surroundings, so the surroundings become cooler. This is why an earthen pot keeps water cool in summer, why acetone on the palm feels cold, why we sweat, and why cotton clothes are comfortable in summer: cotton absorbs sweat and exposes it to air for evaporation. Water droplets on the outside of a glass of ice-cold water are water vapour from the air condensing on the cold surface.

Worked examples

Example 1: Heat needed to melt ice

Question: How much heat is needed to melt 2 kg of ice at 0 °C into water at 0 °C? Latent heat of fusion of ice = 3.34 × 10⁵ J/kg.

  1. The heat used for a change of state is Q = m × L.
  2. Q = 2 × 3.34 × 10⁵ J.
  3. Q = 6.68 × 10⁵ J.

Answer: 6.68 × 10⁵ J, with no rise in temperature.

Example 2: Why steam burns worse

Question: Why does steam at 100 °C cause a more severe burn than boiling water at 100 °C?

  1. Both are at the same temperature, so temperature is not the reason.
  2. Steam has absorbed the latent heat of vaporisation, 22.5 × 10⁵ J for each kilogram, when it was formed.
  3. On touching skin, steam condenses and gives out this extra energy in addition to the heat that hot water gives.

Answer: Steam carries extra latent heat of vaporisation, which is released on condensation.

Example 3: Earthen pot

Question: Why does water kept in an earthen pot (matka) become cool in summer?

  1. The pot has tiny pores through which water seeps to the outer surface.
  2. This water evaporates from the large outer surface.
  3. Evaporation takes latent heat from the pot and the water inside, so the water cools.

Answer: Cooling by evaporation from the porous surface of the pot.

Common mistakes

  • Saying the temperature rises during melting because heat is being supplied. It stays constant; the heat becomes latent heat.
  • Confusing evaporation with boiling. Evaporation happens at any temperature from the surface only; boiling happens at the boiling point throughout the liquid.
  • Saying high humidity speeds up drying. High humidity means the air already holds a lot of vapour, so evaporation slows down.
  • Forgetting the unit of latent heat. It is J/kg, not J.

Try it yourself

  1. Convert the boiling point of water and the melting point of ice to Celsius, and explain why a desert cooler works better on a hot dry day.
  2. Name two substances that sublime, and state what dry ice is.
  3. How much heat is needed to convert 500 g of water at 100 °C into steam at 100 °C? Latent heat of vaporisation = 22.5 × 10⁵ J/kg.

Answers: 1. 100 °C and 0 °C; hot dry air has low humidity and high temperature, so evaporation and cooling are faster. 2. Camphor and ammonium chloride (also naphthalene); dry ice is solid carbon dioxide, which sublimes at 1 atm. 3. Q = 0.5 × 22.5 × 10⁵ = 11.25 × 10⁵ J = 1.125 × 10⁶ J.

Quiz

Five questions built from this lesson. Start at Core; the level adapts to your score.

Flashcards

Turn the key terms of this lesson into cards that come back just before you forget them.